Home > Hard Drive > New Hard Drive Not Detected Windows 10

New Hard Drive Not Detected Windows 10

Contents

A Full Format will do a Quick Format, then go though every sector of the drive and test it, marking off any faulty ones (very rare) so they won't be used. Before, the cd and dvd drives were e: and f:, the hd(when it was recognized) was still g:Not sure why it happened (I might try removing all emulation drives first and If you can’t see the labels, refer to your motherboard’s documentation. This was done approximately two years ago and, until now, there have been no further problems. http://directcomputerrepair.com/hard-drive/secondary-hard-drive-not-detected-windows-10.html

Stand up for the right to repair in Massachusetts. If your drive does not spin, check that the power connector and interface cable are securely attached. 2. That way it will recognize your Sata drives and install Windows on the drive you select to be the boot drive.I would advise disabling IDE Hard Drives by temporarily removing their You must be sure to set the jumpers to master and slave, this should be identified by the diagram on the drive.I am using the appropriate cables for each drive.You will

New Hard Drive Not Detected Windows 10

My thinking was I would keep my raptor drive and use that to house my Orange Box games from Steam (help with load times) but honestly would the 10,00RPM 1.5GB/S make Cancel LikeARabbit Rep: 3.2k Macalope 9 8 3 Posted: 02/19/2013 Options Permalink History This hard drive SHOULD be compatible with your iMac assuming you do have a 17" Intel iMac. Your primary (boot) drive should be connected to the lowest SATA port on your motherboard, unless otherwise specified in your motherboard documentation.

Make sure that the hard drive is lined up correctly before applying pressure. I had spent about 4 hours on the web over the last 3 days trying all kinds of things that did not work. With that in mind I would be troubleshooting the component itself. Windows 10 Not Detecting Second Hard Drive The connector on each end should "latch" into the socket on the drive and on the mboard, or on the drive controller card - it should not move when you merely

The Windows XP installation process breifly indicates that, in order to install "third party" or "Raid" drivers, function key "F6" must be immediately pressed and, I understand, that it will only New Hard Drive Not Detected Macbook Pro All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. Some older systems may see the drive and classify it as a SCSI device if you are using a Serial ATA host adapter. I right clicked the header on the left to initialize, repeated your steps and all is well.

My SATA conked out, and I wanted to get up and running right away, w/o buying an expensive SATA at a brick&mortar store nor wait 5 days for a it to How To Detect New Hard Drive Windows 10 If you find out any good info, please let me know...thanx!Regards,Robert Flag Permalink This was helpful (0) Collapse - Sata is primary by edersch / July 28, 2005 9:26 AM PDT Your computer may automatically detect your new drive. Take Action It's time to speak out for your right to repair Dear Wyomingites, Wyoming has a chance to become the first state in the nation to pass "Fair Repair" legislation.

New Hard Drive Not Detected Macbook Pro

Take Action It's time to speak out for your right to repair Dear Minnesotans, Minnesota has a chance to become the first state in the nation to pass "Fair Repair" legislation. http://newwikipost.org/topic/3XTzppDofYXYBh70yKbL4DllHZ35VQCY/Should-I-install-SSD-SATA3-on-SATA2-motherboard.html The early Intel iMacs used the SATA I specification of 1.5Gbit/s. New Hard Drive Not Detected Windows 10 View all 7 comments Report steer- Apr 18, 2010 at 08:33 PM Thank you very much!!!! New Hard Drive Not Detected Windows 7 Tell them that you believe repair should be fair, affordable, and accessible.

If you are replacing the primary drive or building a new computer, you will need to install your operating system. http://directcomputerrepair.com/hard-drive/no-hard-drive-detected-dell.html As long as your mobo supports both IDE and SATA and still has a connection for each, then you're fine. Once the optical drive is secured and connected, you can close up your computer and power it back on. Enhanced mode device support must be set on to use a mixed device configuration. New Hdd Not Detected Windows 10

But we need your help. When we hold down the option key and boot from the Snow Leopard Install DVD, and then select Disk Utility from the Utilities menu, no hard drive disk shows up. Disconnect each from the drive by pulling gently on the connectors. 5 Remove the old hard drive. have a peek here SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved.

Flag Permalink This was helpful (1) Collapse - It's about reading mobo doc and following instructions by Doug_Hirschfeld / July 28, 2005 11:10 AM PDT In reply to: It's all about How To Repair Hard Disk Not Detected But despite that, the bios does recognize the drives are there but I can't figure out why XP won't boot. But the issue still persists and I have no idea how to fix it.

You will need to install a new motherboard if you want to use your SATA drive. 6 Finish the installation.

Warnings To protect against electrostatic discharge (ESD), an antistatic wrist strap should be worn whenever working inside a computer tower. Take Action It's time to speak out for your right to repair Dear Kansans, Kansas has a chance to become the first state in the nation to pass "Fair Repair" legislation. While the computer restarts, run the system setup program (sometimes called BIOS or CMOS setup). Bios Not Detecting Hdd After doing further trouble shooting, it did turn out that the SATA cable between the HDD and the motherboard was the problem.

From research that I've done on the internet and because the computer is running Win XP, it seems that a driver for the SATA HDD must be installed. I would try the following: Reinstall the original hard drive and verify that it shows up in Disk Utility - this will let you know that the SATA cables and connections If you do, when you are finished come back here and find the remainder shown as "Unallocated Space". Check This Out See in Thread ↓#1 DanJ May 14, 2012 at 12:46:54 You'll need to "slipstream" the driver into your XP install disc.

So be sure you have the driver on a floppy and it should have come with your motherboard. Report • #2 OtheHill May 14, 2012 at 14:59:55 Get nliteOS from the link below. When your tractor breaks or your cell phone stops working, they want to be the only people who can fix it. by esemones / July 19, 2005 8:12 AM PDT My new computer has a SATA Maxtor drive as the primary.

There are a few additional considerations to take into account if you are running multiple SATA drives in a RAID array (like making sure all OS's are installed with RAID drivers) Our model number is listed as having SATA 3Gb/s, which I thought would be compatible with our machine. 01/26/2013 by Melissa Yatzeck Add a comment 0/1024 Cancel Post comment Are you Find out who represents you in Kansas' legislature. Was this answer helpful?

And they get to set whatever prices they want. By continuing to use our site, you agree to our cookie policy. This is where I currently have windows vista ultimate installed. The safest way to work inside of a computer is to wear an antistatic wrist strap while working on the computer. 3 Insert your new optical drive.

You shouldn’t have to beg the manufacturer for permission to fix it when it breaks. A Serial ATA-compatible power cable or adapter (sold separately).