Home > Hard Drive > How To Slave A Sata Hard Drive

How To Slave A Sata Hard Drive

Contents

Yes it did auto run some scan check on the E drive and mentioned corrupt and then deleting I think, (it's soooo fast) and lately it had alot more that it But the partition is smaller than the actual size of the hard disk. Thank you very much for your instructions. Remove the side panel and place it out of the way. 8 Find the area where all the flat ribbon cables (or SATA cables, which are smaller and usually red) connect http://directcomputerrepair.com/hard-drive/how-to-connect-sata-hard-drive-to-motherboard.html

After you machine posts and the drives are being displayed you can hit the Pause/Break key and it will freeze that screen for you to see if it recogizes the slave. I just installed a 1TB HD via sata controller card, to my Dell pc. RESPECT: James Bruce - simply modest and virtually real Keep up the good work! Format is NTFS. http://www.wikihow.com/Add-an-Extra-Hard-Drive

How To Slave A Sata Hard Drive

Passing along to the co-workers. If this is the case, there may be a better way to transfer the data.4. Will there be any problem with different file formats? To others out there who are stumped by techy terminology, I suggest browsing a little bit more sites & things will fall into place.

is there a way around this? The program Files say 0 files and that it is unaccesable///File or directotu is corrupted and unreadable In the folder that says Documents and settings, only the sample pics that are It did before. How To Install A Second Hard Drive Windows 7 I need the old drive in order to run the image software, as I don't have a boot CD or the windows disks on hand.

teachingazteca August 11, 2008 2:48 pm Reply # I am having a similar problem as Linda below, and Bios picks up my slave drive, but I can't access it or see What Is A Slave Hard Drive Show more unanswered questions Ask a Question 200 characters left Submit Already answered Not a question Bad question Other If this question (or a similar one) is answered twice in this You might need some changes to start up to insure files are being pulled from "D" vice "C". When XP is installed with one hard drive, apparently the default is to not expect a second drive to be added!

Finally, there are four identical slots on the motherboard where the drive data cord attached. How To Slave A Laptop Hard Drive Would you please kindly walk me thru?. Reply travis gibbs on December 22, 2009 at 3:23 am ok i have a old computer may me 4 years or more. But then it just freezes up.

What Is A Slave Hard Drive

You will see your boot drive, it will show partitions and the file system type. http://www.wikihow.com/Add-an-Extra-Hard-Drive On the screen that shows that primary master/slave, secondary master/slave, you should see the name of your new hard drive. How To Slave A Sata Hard Drive I might also note that it was close to full (we were going to burn stuff off it to make room) and the machine came up with a bad sector message How To Install A Second Sata Hard Drive However, it does still boot up and run windows.

Once I slave over the HD will I need to load anything or will it recognize the slave. this contact form After you remove the sides you will have a front and a back so to speak. because exist specfic software for jpg.. If your drive has some type of major file system problem it may show up as "unknown". How To Install A Second Hard Drive Windows 10

NIce to see some floridians.Chaz Reply Tyler Thompson on November 1, 2007 at 11:09 pm Chaz, please register on our forums for more specialized help. How about installing a new and different hard drive in a laptop? I really need to get some email address from the hard drive and some holiday pics. http://directcomputerrepair.com/hard-drive/how-to-connect-ide-hard-drive-to-sata-motherboard.html or are these the only 2 sata ports the ThinkServer has?

Computer Newbies forum About This ForumCNET's computer newbies forum is a great resource for new computer users to find solutions to their computer problems. How To Slave A Hard Drive To Recover Data It is recognized at other prompts. You are going to want to try and push, any cables in the way of the rear of the drive, up and out of the way.

Now my issue is how to retrieve the important files from the old hard drive.

Powered by Mediawiki. by JCHJCH / September 3, 2004 2:08 AM PDT In reply to: Install old hard drive as slave drive? Tried several times making sure all Jumpers are set properly… both drives are the same drives Seagate Barracude IV ATA drives from slightly different model Dell Dimension workstations - both running How To Connect Two Sata Hard Disk In One Pc Go to your local computer store or buy online from Newegg or another retailer.

Reply Robert March 20, 2015 at 11:37 am Can I add my old hardrive to a newer machine? Do not make any other changes in the CMOS settings. Flag Permalink This was helpful (0) Collapse - Very thoughtful responses, thanks by grandpaw7 / September 3, 2004 1:11 AM PDT In reply to: Install old hard drive as slave drive? Check This Out Your motherboard might have some SATA II ports (running at 3Gb/s) and some SATA III ports.

If I put the old drive in an external drive case, can I clone from this location versus the internal cable?Thanks. Reply Geoffrey on January 5, 2009 at 10:25 am This guide helps even those who are good at computers. by R. If you are using an IDE hard drive, you want to optimally connect the drive on a different IDE channel than your DVD/CD drives.

One of the options will manage, click on manage. I read it yesterday and was able to install a new (additional) drive with out any issues. It could just be a corrupt file the local fix-it shop says.So when I use the usb thing with my laptop harddrive inside it, to hook to my desktop or another Step 8: Holding the hard drive firmly, grab the cable and pull it out.

Reply Gwen on February 9, 2009 at 7:18 pm Would like to know the same answer of not format=ting the second (slave) hard drive. I knew the new drive was there and installed correct as I could find it in bios as well as the hardware manager.I did need to explore a little after using The old HD could be placed back in the old pc. anyway, when my dad brought this computer home, we unplugged the compaq and connected the new one, btw its an emachines.

pls is this the best option?, if yes, how do i go about doing that? (pls permit my epistle. This is very useful for noobs that does not have a clue on computers. by rhbass / August 26, 2004 5:52 PM PDT In reply to: Install old hard drive as slave drive? The physical installation was easy - I just needed that last bit of help getting through the Windows XP disk management stage.As I write this, 500gb of new hard disk space

January 1, 2008 4:51 pm Reply # It sounds simple enough. unfortunately it has two drives so I'm starting with #2 thinking that is probably the "D" drive that I use for files, music and pics as opposed to the OS (hoping About The Author PCMech Staff176 Comments Ryan on July 29, 2007 at 1:33 pm For a step by step installation procedure, it would be nice if it was written in plain michael/Mark June 21, 2008 2:23 pm Reply # it does see the HD (even now says Maxtor), however does not have a file system-it is blank.

Report cheefdapot- Jan 9, 2009 at 11:48 AM dude!!!! Thanks a lot!